G110

At times no picture.

Check C2366 (100 nF; 4822 122 33496).

G110

At times no synchronization.

Check capacitor C2366 (100 nF; 4822 122 33496).

G110

Bottom fold over

Check and replace C 2509 (4822 124 40244)

G110

Brightness too high/fly-back line visible

Check/replace IC 7465 (TEA 5101A/P; 4822 209 73832) Check/replace R3375  (180 Ohm;  4822 111 30542)

G110

BUT11AF S.C. AFTER P.SUPP KIT FITTED AND SET RUN I

CHECK - D6612 ,  6614В  (CHECK DRIVE WAVEFORM TO BUT11 ,  SWITCH ON DELAY PROBABLY MISSING  )

G110

Characters wrong

Replace U 1003 (4822 212 23371) non TOP

Replace U 1003 (4822 212 23519)

G110

CHOPPER + LINE TRANSISTORS SC

C2546 8n2В  2kv

G110

Chopper tr blows at sw on even after fitting kit

OK if mains wound up slowly - check on/off sw & Positor in degaussing cct

G110

Chopper tr blows in st/by - ok when ON

D6646, D6649, Tr7655, Tr7656 & Tr7654 cleared the problem

G110

Chopper Tr BUT18AF fails periodically

Fit mod - 2 x BYD73B diodes in series between b - e of BUT18AF (anode to base). Make sure Tr7654 is BC817 not BC845

G110

Colour drifts to the right using the S-VHS input.

Remove: R3433 and R3430. Modify: R3431 into 100 kohm (4822 051 10404). Add: R3428 - 180 ohm (4822 051 10181) between C2432/R3433 and 12  IC7425.

G110

Coloured flash on channel change and VCR features

It is possible that on the G110 chassis a coloured flash may be seen when syncs are interrupted.В  For example when changing channels or on VCR playback in 'still' or 'search' modes. In the case of home video recordings, the edit points may be marked by aВ 

G110

Coloured spots in picture (local dooming).

Service solution: Mount a resistor of 220k ohms in parallel with capacitor 2349 and replace resistors 3891, 3892 and 3922 by 1k2 ohm types.

Modification introduced in products. Sets with production number QG05/AG04.

G110

Contents of memory lost

Replace IC7770 (ST24C02CP; 4822 209 62098)

Mount metal shielding 4822 466 82781 on IC7720 with earth to R 3738

G110

Continuous page header display in subtitle

Change text IC to type MAB8461P/W196 part No4822 209 62479

G110

Contrast adjustment inoperate, colour tails

Diode 6335 defective (4822 130 80446).

G110

Contrast variations with subtitling in sets with BL-CRT.

1) Add a SMD capacitor of 1nF - 5322 122 31647 between pins 3 and 4В  of connector 20G of the CRT panel.2).  Add C2336 - 1nF - 5322 122 31647 between pins 3 and 4 of connector 14G on the mono carrier. Modify R3715 into 220k - 4822 051 10224. Adjust PP valu

G110

Dead - 140v rail down.

Change rectifier diodes - may check Ok when cold!

G110

Dead - BUT18AF s/c in psu

Flyback tuning cap C2546 8n2 2kv low value and EHT lead s/c

G110

Dead - psu ok on dummy load

C2546 8n2 & C2550 390nF in LOP stage

G110

Dead - s/c in lop stage

Scan coupling cap C2550 390nf 250v s/c & bulging

G110

DEAD BUT POWER SUPPLY WORKS ON DUMMY LOAD . OR LIN

C2546 8n2В  C2550 390nF

G110

Dead chopper transistor s/c.

Also change CNX83A optocoupler part No.4822 130 82034

G110

DEAD FUSE SHATTERED

FIT POWER SUPPLY SERVICE KIT

G110

DEAD HT LOW AT 20v ISOLATE PIN 3 LOPT + SET STARTS

SHORT ON 12v RAIL OR POSS Q7284

G110

Dead -PSU rep kit fitted; HT low at 40v

R3616 100R risen to 1k

G110

Dead with electronic trip operated

To dis trip remove R3660 - this resulted in E-W dist; T1534 315mA Wickman fuse o/c

G110

Does not function

Remove connector G15 and connect lamp to +148V. Lamp does not burn.

Replace TS7625 (BUT18AF; 4822 130 61407) Build-in SOPS repair kit (SBC7020) Apply at the same time 2 diodes (BDY73; 4822 130 60778) in series between basis and emittor of TS7625 (anode

G110

Does not function well

Replace IC 7720 (TMP47C634N-2475; 4822 310 31844)

Important: also mount metal shielding with earth to R 3738

G110

F2 error & no sound

check 9v supply to NICAM board

G110

Field bounce/rolling

C2465 220 16v - 12v smoother

G110

Field lin poor

C2509 22 50v

G110

Ghosts and poor colours

SAW filter 1016 (4822 242 72374).

G110

Goes dead when sw to st/by (no LED) - ok if sw on again from mains

D6657 20v zener

G110

HINTS WHEN REPAIRING THE G110 POWER SUPPLY. 

HINTS WHEN REPAIRING THE G110 POWER SUPPLY.

While fitting the G110 Power supply Repair kit check fuse 1559 in the 8V feed from the Line Output Transformer. This Fuse can fail as a result of a defective Power Supply. This 8 Volt feed is used in the Powe

G110

Int dead

dry joints chip res R3619

G110

int off - no leds

pin 18 lopt dry joint

G110

Int partial field collapse

1R chip res in emitter BD234 fop tr on underside of pcb

G110

Int pic blanking with fb lines

12G & H supply lines low at 6v - R3912 dry jointed

G110

Int start & no st/by

D6657 16v monitor diode leaky

G110

INT START NO STBY

D6657В  ( 20v ZENER )

G110

Int/no col

4.43Mhz osc badly dist - fit earth to xtal clip

G110

Lines, parts of pic blanked & no Txt

IC7830 SAA5231 txt proc chip

G110

Low contrast of teletext

In cases of specific complaint, the contrast in teletext mode can be increased by removing D6813 (LLZC7V5).

D6813 is a chip component mounted on the print side of the teletext decoder panel 1003.

G110

Mono/Stereo-indication switches

Connect a capacitor (1 uF; 4822 124 20722) and a resistor  (1,5 MOhm; 4822 111 50452) in parallel. In series with this circuit a diode (1N4148; 5322 130 30621) is connected (cathode on R/C). Mount this D/RC circuit between pin 3 of IC 7220 (stereo-decoder

G110

No AV pic when scart connected

AV sound ok but off air pic remains - IC7720 TMP47C634-2676 faulty

G110

no line deflection

Transistor 7545 (4822 130 61265) defect

cause: pins of line transformer 5541 bad soldered.

G110

No pic - sound ok

No 200v supply to RGB as R3375 180R o/c - caused by IC7465 TEA5101A/P RGB o/p IC s/c

G110

No picture, no sound

Remove connector G15 and connect lamp to +148V. When lamp does not light up, build-in SOPS repair kit (SBC7020) (4822 310 20489)

Apply at the same time 2 diodes (BDY73B; 4822 130 60778) in series between basis and emitter of TS7625 (anode to basis)

G110

No picture, no sound.

Only snowy picture from presets. On pin 19 of SCART no video signal. External signal supplied to pin 20 SCART is processed well.Replace U1000 (UV816; 4822 210 10365)

G110

No picture, sound OK. Clock (8,86 MHz) on pin 28 IC 7350 is OK

Replace IC 7350 (TDA8390/N4; 4822 209 61027)

Modifications if replacing TDA8390/N3 remove R3340; remove R3341; change R3371 into 1,2OhmВ В  change R3372 into 680 kOhm; remove D6336

G110

No picture, sound OK. No 8,86 Mhz on pin 28 IC7350.

Replace Q1352 (4822 242 70323)

G110

No sound nor picture. No line oscillation

Starting voltage missing in line oscillator. Diode 6455 (LLZ-C2V7;4822 130 81138) defective.

G110

No sound, picture OK

Replace IC 7260 (TDA 8425/V1; 4822 209 73213)

G110

No sound, picture OK

Picture is present and the selection of programs functions. Check/replace IC 7220 (TDA 1521/N4; 4822 209 73853)

Check/replace IC 7220 (TDA 8405/V2; 4822 209 72371)

Check/replace IC 7260 (TDA 8425/V1; 4822 209 73213)

G110

No sound, wont stop when searching & goes to st/by aft 10mins

No sig ident volts pin 13 IC7470 TDA2579A (should be 9v with sig, 0v with no sig). Replaced TDA2579A & C2451 01 sm cap which was blowing the chip

G110

No start up & trips when LOPTx dis'd

TS7591 BC858 s/c

G110

No tune store

TDA2579 ic

G110

no txt 

dry joint link on 12v supply on txt pcb

G110

No TXT; oscillator on TXT decoder does not function.

Add C2802, C2803 15pF (4822 122 32504) on the teletext module U1003.

G110

Noise in picture

IC7425 (TDA4565; 4822 209 71512) defective.

G110

off

ok when s/c prot line - D6657 (LLZ-C20) 16v supply monitor

G110

off

if low res across lop tr (<1k) check lop tr lopt C2550, C2545 1n2 2kv

G110

One inch black band down lh side of screen

Tr7594 BC848 & Tr7593 BC858 sm s/c

G110

OSD partly disappeared from the screen in BL sets.

Modify C2758 and C2702 from 12pF into 10pF (4822 122 31971).

G110

Page 811 appears spontanuously

Decoder selects page 811 and blocks

Mount new uP (IC 7800) MAB 8461P/W196 (4822 209 62479) on TXT-Decoder.

G110

Pic shifted & black line down centre of screen

TDA2579 pin 12 has leak to chassis due to solder bridge

G110

Picture distorted

Vertical pulse incorrect. Check capacitor C2500 (220 pF; 4822 122 31965).

G110

Picture moved and a black bar in the middle of the screen

Tinbridge over C2460. Pin 12 in TDA2579 leaks.

G110

Picture twists from top

Voltage of pin 8-IC7450 (TDA3654Q) on the LSP has raised to ca. 20 V.

В Check diode 6451 (BZX79/C5V6; 4822 130 80954).

G110

Poor in contrast.

Replace T7413 on the picture tube PCB (BC856B; 4822 130 60373).

G110

POOR SOUND ON LH SPEAKER ON NICAM ONLY

IC7530 + IC7531 LM833В  (ONE LH ONE RH )

G110

Poor width reg with brightness (HT constant)

sm C2526 8n2 leaky

G110

Protection of T7625 (BUT18AF)

Protection of T7625 (BUT18AF) A production change is being introduced adding two diodes connected in series between the base and emitter of TS7625 (anodes towards base).В  The type no. for the diodes is BYD73 service code no. 4822 130 60778

Reason:  To i

G110

Red flashing when changing chs using VCR.

Mod see Tv Mag.

G110

Replacing TDA2579

Replacing TDA2579. During production, IC7470 TDA2579 versions N6 and N7 were replaced by TDA2579A/N8. At the same time the values of the following components were also changed.

G110: Position N6, N7 and N8 Code C2466 4.7uF 6.8uF 4822 124 20727 C2468В  1uF

G110

Replacing the EAROM

Replacing the EAROM: The memory IC in these receivers has been replaced by type ST24C02CP (code no. 4822 209 62098). On some receivers however, the circuit will have to be modified. If the ST24C02CP is being fitted in place of an X2402 no circuit changes

G110

SCART SOCKET WON'T SWITCH VIDEO OVER BUT DOES SWIT

TMP47C634-2676

G110

Screen goes blnk with Txt lines on Chan change

R3917 safety res o/c,(12v supply), SAA5231 vid proc chip got hot prior to it going - caused by L5803 6Mhz tuning coil

G110

Servicing the Philips G110 Chassis

See TV Mag Dec 1995 & Nov 1996

G110

Set blocked; no control of functions.

Check solder joints of resonator 1760.

G110

Set blocks

No functions possible anymore Replace IC 7720 (TMP47C634N-2475; 4822 310 31844)

Important: also mount metal shielding with earth to R 3738

G110

Set will scan but not stop if chanel found

Check pin 13 TDA2579 for 0V rising to 9V when signal present C2451  ( 0.01uF )  & IC

G110

Slow start up & won't sw to st/by with no sound & pulsing pic (usually after psu rebuild)

R3617 220R sm  o/c in psu pri

G110

Sometimes the SOPS will not start up.

Replace 3617 which is fitted across 6617 (220 ohm; 4822 111 90178)

G110

Sound abswent with 'F2' in display

Black wire that supplies 9v to NICAM board  (to D6661 cath component side) was detached

G110

Sound distortion on lh chan - ok on fm sound

TDA1543 DA converter chip in Nicam cct faulty

G110

Sound mutes spontanuously

Mount two capacitors of 100 nF (5322 121 42578; in parallel) betweenВ  pin 10 IC 7220 (stereo decoder) and earth.

G110

Standby Thyristor goes short circuit when switching to standby.

Checks in the Power Supply showed that TR7651 was open circuit Base/Emitter.

Service Code 4822 130 42513.

G110

Start up and run perfectly all day. But if it was

20V zener diode D6657.

G110

Striations

Under certain picture conditions, vertical striations may be seen at the left side of the picture on some receivers only.  Sets mostly affected are those fitted with a .4 version of the CRT base panel.  The symptoms can be greatly reduced or cured complet

G110

sync fault - loses line lock

Tr7364 BC858 o/c due to s/c o/p print to screening can on txt pcb

G110

Text does't function

Replace U 1003 (4822 212 23371) non TOP

Replace U 1003 (4822 212 23519) TOP

G110

Ticking sound

On some receivers it may be possible to hear a ticking noise in the background when the receiver is in external AV mode.

In cases of specific complaint, the phenomena can be reduced by modifying the NICAM panel as follows:

1. Remove chip resistors R3044

G110

To disable control cct if set trips

s/c pins 1 & 2 of opto coupler & run set on reduced mains (about 90v ac) to check psu; cause of tripping was D6657 LI-C20 diode in sound prot line leaky

G110

Transistor 7625 (BUT18AF) lasts longer

Add two diodes BYD73B (4822 130 60778) between base and emitter of 7625 (anodes towards base). Check the 7654 is BC817 and not BC847.

G110

Tuning unstable

Voltage on pin 11 U 1000 (Tuner) fixed

Replace U 1000 (UV 816; 4822 210 10365)

G110

Txt unlocked - appears over pic int

dry joints txt pcb - sm cap in this instance

G110

txt waves about at top

C2829 47 on txt pcb

G110

Vertical bars on channel 2 and 4.

For sets equiped with a .4 picture tube panel, on channel 2 and 4 there are vertical bars (spook) visible at the left side of the picture. To solve this problem remove on the picture tube panel capacitors 2417, 2418, 2419 and replace jumper 9302 by a cap

G110

Vertical shift incorrect, after replacing a 28' BL-CRT.

Mount in parallel of R3512 a resistor of 2K2 (4822 116 52256) or 2K7 (4822 116 52263).

G110

Very low contrast.

Check DC voltage on pin 7 of IC7350.  If this voltage does not rise above 1.7 volts suspect a fault in the BCL line. Check/replace T7351 - BC848B (5322 130 41982).

Check/replace T7413 on the picture tube PCB (BC856B; 4822 130 60373).

G110

When Chopper or LOP Trs goes s/c

Check C2546 8n2 2kv

G110

White area visible on right side of screen in EXT1 mode of BL sets.

Remove the resistors 3462 and 3464. Add a potentiometer of 47K (4822 100 11371) on the position of R3461.

G110

Width at max or int (after LOPTx replacement)

R3525 10k width pot o/c

G110

Width excessive & varies with brightness

C2526 6n8 sm cap in EW mod cct leaky

G110

Will not start; +148V = +/- 20 volts

Fault suspected in Line output stage. Disconnect pin 3 of LOT transformer.  If +148V comes to normal and line drive is achieved; reconnect pin 3 of LOT and try disconnecting R3281 (location D4 of PCB).В  If set starts up, suspect T7284 audio protection tra

G110

Wont power up unless pin 3 LOPTx dis'd

This is the 14v supply which feeds 12v reg. Q7284 BC858 sm in audio prot stage was leaky

G110

Won't start up - P.S squeals. Voltages lower than normal.

Sound IC defective. After replacement, PS protection active- Change also 7281&7282(BC848) near sound IC

G110

Won't start up - P.S squeals. Voltages lower than normal.

Sound IC defective. After replacement, PS protection active- Change also 7281&7282(BC848) near sound IC

G110-PTV

Addition to parts list

Addition to parts list. The EHT cable CRT to splitter (3) is available under code numberВ  4822 320 20192.  Please add to the parts list in the G110 PTV chassis service manual.

G110-PTV

Excess width

C2549 10 50v in EW Corr cct

G110-PTV

Excessive width

In the case of excessive width, it is possible that C2549 (east/west circuit) is low capacity.To improve reliability an alternative type of capacitor should be used as a replacement. However, the dimensions of this capacitor are different from the origi

G110-PTV

Horizontal adjustment does not work. Picture too wide.

Elco 2549 (10uF) capacity reduced. Replace by code 4822 124 80275 (mechanically bigger).

G110-PTV

Preventive action

Preventive action .  After replacing a projection tube, the deflection coil may shift downwards. To keep the deflection coil on its correct location, the coil should be glued to the new projection tube.Adhesive 4822 390 30066 should be applied between t

G110-S

Bad picture sharpness

Only for 21GR6766/56, 25GR6766/56, 28GR6776/56 serial numbers SV009025 or lower

Change 3481 SMD to 510R (4822 051 10511)

Change 3483 SMD to 100R (4822 051 10101)

Change 3484 SMD to 1k  (4822 051 10102

For 21' sets: On the conductor side of the main p

G110-S

Picture jumping when switching from PAL to NTSC M

Place on copper side across item 2503 +VE to +VE and -VE to -VE of item 2503 a capacitor of 1uH 20% 50V (4822 124 40242).

REMARKS:  Introduced in production in week 9252

G110-S

Set dead; during switch-on, LED momentarily  on  with amber light.

Two possible solutions:

1. Replace uP IC7200 by TMP47C634N-R364 (4822 209 31492) and   keyboard pos 1210 by 4822 218 21032

2. Upon switching on, if the set is hung, do the following initialising for the uP  - Switch off the set. Disconnect pin 41 of uP

TV - Techniker

G110

Vertikal starke LinearitРґtsfehler oder Vertikalablenkung zu klein

C 2509 Kapazitaetsverlust

G110

Keine Funktion

Si1600(2AT), T7625(BUT18AF) Nach 3-5 min. wieder defekt! Netzteil-Servicekit SBC7020 einbauen (Bestellnr. 4822 310 20489)

G110

Bildbreite und Ost-West

Poti3525(10kohm)

G110 SVHS

Kein Bild, kein Ton (Schutzschaltung spricht an)

C2550(390nF/250V)